Skip to content
Aqualarm

How the system works

Aqualarm is a closed loop: detect water, decide, close the supply, then tell someone. It keeps protecting the property locally even if Wi-Fi or the internet is down.

  1. Sensor units

    NEW End Unit, End Unit or Door Unit detect water or take a command.

    434.7 MHz radio

  2. Main Unit+

    Receives the alarm, sounds the buzzer and drives up to two valves.

    Valve cable

  3. Actuator valve

    Closes the incoming supply pipe.

  4. Gateway

    Paired with the Main Unit+ by radio. Sends the alert over Wi-Fi to the app, or by dry contact to a BMS.

Three parts protect the property

Sensors

NEW End Units, End Units and sensor wires or plates detect water and report it to the hub. Battery units last more than two years and use 434.7 MHz radio.

Sensor units

Main Unit+

The hub receives every sensor signal, sounds the alarm and tells the valves to close or open. It also passes alerts to a gateway.

Main Unit+

Actuator valve

A motorised ball valve on the incoming supply. On command it closes in one movement, stopping water to everything downstream.

Actuator valves

Choose a control unit

Each control unit drives up to two valves. The difference is how sensors connect and whether the system can report to an app.

FeatureMain UnitMain Unit+PowerStop
SensorsWired onlyWired, plus up to 10 wireless1 wired sensor
Actuator valves222
Gateway and appsNoYesNo
Supply12 V DC12 V DC220 V AC socket
Cuts appliance powerNoNoYes
Frost protection below 4 °CYesYesNot specified

Alerts on your phone or your building system

A gateway links the Main Unit+ to the cloud. Homes use the IoT Aqualarm app. Property managers use IoT Aqualarm Pro, with a web dashboard for many sites, or connect the Gateway Link Pro to a BMS by dry contact.

  • IoT AqualarmFor homes. Works with Gateway.
  • IoT Aqualarm ProFor businesses. Works with Gateway Pro and Gateway Link Pro.
IoT Aqualarm Pro dashboard on a desktop monitorIoT Aqualarm app on a phone

Alarm types

Every fault has its own alarm, so users know what happened and what to do next.

Water leakage
A sensor has detected water. The valve closes and the hub sounds the alarm.
Low battery
A battery-powered sensor unit needs a new CR2450 cell.
Disconnection
A sensor unit or valve has stopped responding to the hub.
Low temperature
The hub has measured below 4 °C and closes the valve to protect pipes from freezing.
Sensor port
A wired sensor port reports a fault. Fit a dummy plug in any port you are not using.
Setup matching
The hub is in pairing mode, ready to add a sensor unit.
Valve self-test
The 5-day valve exercise found a problem with valve movement.
Wi-Fi disconnection
The gateway has lost its Wi-Fi connection. Local protection keeps working.

Inside the actuator valve

Fit the valve with a complete Aqualarm system or on its own as a smart valve. In multi-storey buildings, a valve on every floor can be monitored and operated from one control room.

Actuator valve
  • Ball valve

    A steady opening and closing speed gives accurate flow control and reduces stress on the pipework.

  • Manual wheel and automatic operation

    Lift the manual wheel to operate by hand, so you stay in control during a power cut.

  • 5-day self-test

    The valve turns every 5 days to keep it moving freely. The water supply is not interrupted.

  • Mechanical torque limiter

    Protects the gearbox from mechanical overload and extends the life of the valve.

  • Position indicator

    Shows the valve position at a glance, including when it is only part-way open.

  • Material options

    Brass for drinking water, bronze for flushing and sea water. Other materials for project orders.

  • IP65 and PN16

    Dust-tight, protected against water jets and rated for pressures up to 16 bar.

  • Soft closing

    A soft-closing mechanism and mechanical slide block reduce wear and water hammer.

PowerStop

PowerStop: cut the power, not just the water

Plug a washing machine or dishwasher into PowerStop. When its sensor detects water, PowerStop switches off the appliance so water never meets a live circuit, and closes up to two actuator valves.

It can run the valve self-test manually, works on its own or with the rest of the Aqualarm range, and is available for different plug types.